Skip to content

The Infrared Radiation Required Practical: Leslie Cube, Method and Results

A step-by-step guide to the infrared radiation practical: using a Leslie cube and an infrared detector, or cans of hot water and thermometers, to compare matt black, white and shiny silver surfaces. Covers variables, safety, a worked results table, errors and what your conclusion should say.

Published · 8 min read

On this page

In this practical, you find out how the type of surface changes the amount of infrared radiation an object gives out or takes in. Every surface you test is kept at the same temperature, or the same distance from the same heater, so the surface is the only thing that changes.

The usual way to test emission is a Leslie cube: a hollow metal cube with a different finish on each side, filled with hot water. An infrared detector, kept at a fixed distance from one face after another, shows how much each surface gives out. Schools without a detector often use identical cans of hot water, painted or wrapped in different finishes, and compare how fast each one cools.

The result is the same either way. Matt (dull) black is the finish that gives out and takes in infrared best. Shiny silver does worst at both. It reflects most of the infrared that arrives, so it absorbs little, and a poor absorber is also a poor emitter.

What are the variables?

  • Independent variable: the surface finish, such as matt black, matt white, shiny black or shiny silver.
  • Dependent variable: the detector reading, or the temperature change over a fixed time.
  • Control variables: the temperature of the water, the distance from the detector or heater, the size of each surface, the volume of water in each can, and the time between readings.

How do you carry out the Leslie cube test?

  1. Put the cube on a heatproof mat, with one face pointing at the infrared detector.
  2. Fill the cube with water just off the boil, where it stands, and put the lid on.
  3. Measure the distance from the face to the detector with a ruler, for example 5 cm.
  4. Wait until the reading steadies, then record it.
  5. Turn the cube to bring the next face round. Keep the same distance and record again.
  6. Work round all four faces, then go round again in the opposite order and find a mean for each face.

The water cools all the time, so work quickly. Going round in the opposite order the second time stops one face always being measured last, when the water is coolest.

What if there is no infrared detector?

Use identical metal cans, each with the same volume of hot water, a lid and a thermometer.

  1. Paint or wrap each can in a different finish.
  2. Pour the same volume of hot water from the same kettle into each can, and check that they all start at the same temperature.
  3. Record the temperature of each can every 2 minutes for 10 minutes.
  4. The can that cools fastest has the best emitter on its surface.

To compare absorbers, swap the hot water for cold water. Stand the cans the same distance from a radiant heater or a bright lamp and record how fast each one warms up. Another version uses two metal plates, one matt black and one shiny, with a drawing pin stuck to the back of each with wax. The pin on the better absorber drops off first.

How should you record the results?

Use one row for each surface. Head each column with the quantity and its unit, such as "temperature at start / °C". A bar chart suits the results, because the independent variable, the type of surface, is a category rather than a number.

Worked example: four cans cooling

A class in Dubai pours 250 cm³ of water at 80.0 °C into four identical cans with lids. After 10 minutes, they record these temperatures (example values):

SurfaceTemperature at start / °CTemperature after 10 min / °C
Matt black80.067.5
Matt white80.068.0
Shiny black80.068.5
Shiny silver80.074.0

Step 1, temperature drops: matt black 12.5 °C, matt white 12.0 °C, shiny black 11.5 °C, shiny silver 6.0 °C

Step 2, average rate of cooling: matt black 12.5÷10=1.2512.5 \div 10 = 1.25 °C per minute, and shiny silver 6.0÷10=0.606.0 \div 10 = 0.60 °C per minute

Step 3, compare: 1.25÷0.60=2.11.25 \div 0.60 = 2.1, so the matt black can cooled about twice as fast as the shiny silver can

Answer: matt black is the best emitter here and shiny silver is the worst.

Two details are worth noticing. First, the shiny silver can still cooled by 6.0 °C. All four cans also lose energy by conduction and convection to the air around them, and those losses hardly depend on the finish. That is why a thermometer shows smaller differences than an infrared detector, which picks up only the radiation. Second, matt white came very close to matt black. The next section explains why.

Why do the surfaces behave differently?

When infrared reaches a surface, it is absorbed, reflected or transmitted. A shiny metal surface reflects most of it, so it absorbs very little. A matt black surface reflects very little, so it absorbs most of it.

Surfaces that absorb infrared well also emit it well. So a matt black surface, which warms up quickly in front of a heater, also cools down quickly once it is hotter than its surroundings. A shiny surface is poor at both.

White is the surprise. White paint reflects most visible light, which is why white walls stay cooler in sunshine. But warm objects give out infrared, not visible light, and for infrared, ordinary white paint behaves almost like black paint. In exams, rank black above white and dull above shiny. In the lab, do not be surprised if matt white comes close to matt black. Shiny silver really is far behind.

What are the common sources of error?

  • The water cools during the test. Work quickly, and record the water temperature with each reading.
  • Different distances. Measure the distance to the detector every time, from the face itself.
  • The detector warms up when it sits close to a hot face for a long time. Move it away between readings, then put it back at the measured distance.
  • Unequal starting temperatures in the cans. Fill them together, or compare temperature drops.
  • Evaporation from open cans. Use lids, so the surface finish has more effect on the result.
  • Readings taken only once. Repeat, find a mean and look for anomalies.

What should your conclusion say?

A strong conclusion names the pattern, gives the evidence and explains it. For example: matt black emitted the most infrared and shiny silver the least. Shiny surfaces reflect most infrared instead of absorbing it, and a poor absorber is also a poor emitter. Then evaluate it: say how close the repeats were, and whether the differences between the surfaces were bigger than the spread in your repeats.

How can you see it in a simulation?

In the conduction, convection and radiation simulation, choose Radiation under the stage and keep the Test on Emitting. The cube starts with water at 80 °C and the detector 10 cm away. Press Turn to bring each face round, then Record to add the Detector reading to the results table. Readings taken later come out lower, because the water cools. Then switch the Test to Absorbing. Two plates face a heater, and each has a pin held on its back with wax. The black plate's pin drops, while the shiny plate's pin stays on.

For the wider theory, see our guide to conduction, convection and radiation and our guide to black body radiation.

Common mistakes

  • Changing more than one thing. Same water temperature, same distance, same size of surface: only the finish changes.
  • Saying shiny surfaces absorb infrared and then reflect it. They reflect most of it straight away.
  • Mixing up emitting and absorbing. Hot water inside tests emission. A heater outside tests absorption.
  • Ranking by final temperature when the starting temperatures differ. Compare temperature drops.
  • Drawing a line graph of surface against reading. The surfaces are categories, so draw a bar chart.

Key points

  • Keep everything the same except the surface, then compare detector readings or temperature changes.
  • Matt black is the best emitter and absorber of infrared. Shiny silver is the worst at both: it reflects most infrared, so it absorbs and emits little.
  • A good absorber is a good emitter.
  • White reflects visible light well, but in the infrared it can emit almost as well as black.
  • Plot a bar chart, because the type of surface is a category.